Canadian Canoe Routes
http://www.myccr.com/phpBB3_PROD/

4 - 6 oz. fiberglass cloth
http://www.myccr.com/phpBB3_PROD/viewtopic.php?f=49&t=11663
Page 1 of 1

Author:  Doug [ February 19th, 2005, 2:09 pm ]
Post subject:  4 - 6 oz. fiberglass cloth

Other than 2 oz. what are the differences between the 4 & 6 oz. fiberglass cloth?

Which is one is the tighter weave?
Which one takes more epoxy?
I assume that the 6 oz. cloth is denser and thus stronger?

Any websites out there concerning this?


Thanks,
Doug

Author:  recped [ February 19th, 2005, 4:29 pm ]
Post subject: 

Ask an expert...Smithcraft Fibreglass Supply Centre (Toronto)

http://webhome.idirect.com/~edd/smith.html

Website has a lot of dead links but you could call them. Don't really know how "expert" they are but when I asked "how much epoxy do I need for this strip of Kevlar on the bottom of my canoe" the answer was...."This much" and they were EXACTLY right.

My second question was "is this epoxy as good as that stuff which costs a lot more" the answer was "it's the same stuff except for the labels" Too early to tell if he was right but it seems to be holding well.

Ben

Author:  Jwinters [ February 20th, 2005, 6:56 am ]
Post subject: 

For a good discussion on cloth etc. check out

http://www.johnrsweet.com/Fabric.html

Author:  Dan Lindberg [ February 21st, 2005, 12:20 pm ]
Post subject: 

And after you read the stuff on Sweet's site John links to.

Do some searches for fiberglass and Hexcel and BGF.

Hexcel and BGF appear to be the to "biggies" in the glass fiber/weaving business. They both have specification down loads that will allow you to compare different fibers and weaves.

In general, there are a large number of different weaves and cloths, for example, you might find 5 or 6 patterns all around 6 oz/yd, and all with different strengths.

Without knowing the weave pattern/model number, it's hard to tell much of anything about a given cloth. Note that Hexcel and BGF in general use a different numbering system for their weave patterns, though some are the same.

Dan

Author:  daver [ February 21st, 2005, 12:30 pm ]
Post subject: 

http://www.compositescanada.com has a lot of good info,

Author:  Boneli [ February 21st, 2005, 1:04 pm ]
Post subject: 

http://www.bearmountainboats.com/

Some here will be able to give you some answers since everyone is either in the process or has built many canoes.

I have only used 6 oz both inside and out. If I were to do it again, 6oz on the outside and 3 oz on the inside.

Boneli

Author:  Doug [ March 5th, 2005, 7:51 am ]
Post subject: 

If my upcoming Osprey is 47 square feet ( http://www.greenval.com/weight.html ).
What would the weight difference be between, glassing it in 4 vs. 6 oz cloth?

When it refers to the weight in oz., what is it a measurement of?
a square inch?

Thanks,
Doug

Author:  jjoven [ March 5th, 2005, 8:48 am ]
Post subject: 

the weight referrs to sq yard.But that doesn't include the resin. It takes less resin to wet out and fill 4 oz.

Author:  PeterPan [ March 14th, 2005, 8:42 pm ]
Post subject: 

It is pretty close if you just double the cloth weight. So 4 ounce needs 8 ounces/square foot, inside and out. 8 oz being the glass and resin combined total.

Author:  moe f [ March 15th, 2005, 7:55 am ]
Post subject: 

PeterPan said:

Quote:
It is pretty close if you just double the cloth weight. So 4 ounce needs 8 ounces/square foot, inside and out. 8 oz being the glass and resin combined total.


I presume you meant per square yard, otherwise the Osprey with 4 oz cloth would weigh in at about 47lbs for the glass and epoxy alone. My BobSpecial came in at 46lbs with 6 oz and ash gunwales and seats

cheers

moe.

Page 1 of 1 All times are UTC - 5 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/